Talk about the different types of faucet installation.
In the entire home decoration, only the kitchen and the bathroom are used for the faucet, but although only these two places will be used, the types of faucets used are also various. The installation of different faucets will also be different. Today, I will introduce you to the installation methods of various faucets.
Before installation, you must first prepare the installation tools. Check whether the matching parts are complete before installation. Common faucet parts include: hoses, rubber washers, showers, water, kidnappers, decorative caps, etc. Next, we will introduce the installation methods of various faucets.
First, the installation of single hole kitchen faucet
The requirements are stable, because the kitchen faucet is used frequently, and it is moved and moved, so it is easy to loosen, so the lock nut must be tightened. At present, some faucets appear on the market for the screw to increase the nut fixing. This kind of stability effect is very good. If it can solve the problem of water removal, it will be a popular trend in the future.
Second, the installation of single hole basin faucet
When buying a single-handle basin faucet, you should pay attention to the diameter of the water outlet. Most of the market is now a hard tube, so you should pay attention to the height of the water inlet. The 35 working points from the basin are most suitable. When installing, be sure to choose a special angle valve, and the angle valve must be fixed with the hot and cold water pipe of the wall outlet. When you find a distance between the angle valve and the water pipe on the faucet, purchase a special extension tube to connect. Remember, don't use other water pipes to connect, because if the water pressure is too large, it will easily fall off and leak, causing damage to you. If the inlet pipe is too long to exceed the outlet pipe, you can cut off the part according to your needs. If the angle is not suitable, bend it to the position you need as needed.
Remember: Do not bend hard to 90 degrees or more than 90 degrees. When installing the basin to remove water, please don't forget to buy the small interface of the faucet (the faucet is shorted). Don't forget to flush the water pipes buried in the wall before you install it.
Third, the installation of shower, bathtub faucet (wall)
When you have purchased a shower, bathtub, or wall faucet, you can choose the right height to bury the water pipe. The spacing between the hot and cold water pipes must be 15 cm. Before installation, you must not forget to rinse the water pipe to avoid excessive water quality and damage to the faucet.
Installation of shower, bath faucet: After purchasing the concealed faucet, the sump's spool should be pre-buried in the wall. Be sure to pay attention to the thickness of the bathroom wall before embedding. If the wall is too thin, the spool will not be buried. The plastic protective cover of the valve plug should not be easily removed when it is buried, so as to prevent the cement and other chores from damaging the valve core when it is buried. In addition, when pre-burying the valve core, you should also pay attention to the up and down and left and right directions of the valve core to avoid the valve core being buried. When the wall mounted faucet is pre-buried into the water pipe, the size is deviated, and the adjustment can be used to adjust the position.
Fourth, the installation of thermostat
Before installing the thermostatic faucet, please check if the water pipe is left hot and cold right. Remember not to connect the hot and cold water pipes incorrectly, so as to prevent the faucet from working properly. Gas and solar water heaters cannot use thermostatic faucets because the water pressure is too low. Install a thermostatic faucet, please don't forget to install a hot and cold water filter.
Concerned about surprises
Label: The different types of installation of the faucet are different.
Previous: Different crafts have different choices of wooden doors and tricks Next: How to buy high quality sliding doors
A mudflap or mud guard is used in combination with the vehicle fender to protect the vehicle, passengers, other vehicles, and pedestrians from mud and other flying debris thrown into the air by the rotating tire. A mudflap is typically made from a flexible material such as rubber that is not easily damaged by contact with flying debris, the tire, or the road surface.
Mudflaps can be large rectangular sheets suspended behind the tires, or may be small molded lips below the rear of the vehicle's wheel wells. Mudflaps can be aerodynamically engineered, utilizing shaping, louvers or vents to improve airflow and lower drag.
custom molded Mud Guards are made from durable, rubber that's as tough as nails (or rocks for that matter). With a growing number of "No Drilling Required" applications, they're easy to install, conform perfectly to your fenders, and protect your ride and those around you from the rage of the road. Let them splash guards do the work.
Company information:
RenqiuXingcheng Rubber Products Co., Ltd. is located in the side of the Baiyang lake, our company is professional manufacturer of rubber products. We are one of the leading rubber company in china,The company is a private enterprise which is engaged in scientific research, production, sales and service and has obtained ISO 9001 certification. Our main business is producing all kinds of rubber products, including anti-skid plates, Rubber Sheet Series, Rubber Mat Series and horse mat series ect., The products are shockproof, anti-wear, anti-high and low temperature, anti-aging, oil resistant and chemical resistant in character.At present, our products have been sold at home and abroad and mainly exported to Canada, Germany, Chile, etc. We welcome domestic and foreign merchants to negotiate and cooperate with us. We are willing to join hands with old and new friends in creating a better tomorrow.
Rubber Mud Flap,Heavy Duty Rubber Mud Flaps,Rubber Mud Flap For Trailer,Truck Rubber Mud Flaps
Renqiu Xingcheng Rubber Products Co., Ltd. , https://www.xingchengrubber.com