Talking about the Installation and Maintenance of LED Explosion-proof Lamps and Precautions
As the LED is a solid-state cold light source, it has the advantages of high electro-optical conversion efficiency, small heat generation, low power consumption, operating voltage is safe and low voltage, long service life, etc., and low energy consumption; therefore, high-power white LEDs are explosion-proof lamps, especially Portable explosion-proof lighting is a very ideal light source. LED explosion-proof lights for outdoor use require a waterproof drive. Led explosion-proof lights used at gas stations need shockproof!
<br> <br> proof lamp installation and maintenance checkup from the plate before mounting the product specification: explosion-proof type, class, grade, group; housing degree of protection; Installation and fasteners required for mounting the like. The installation of explosion-proof lights must be securely secured, the fastening bolts must not be replaced, and the spring washers should be complete. The dust-proof and waterproof seals should be placed as they are. When the cable enters the line, the cable and the sealing gasket should be closely matched. The section of the cable should be round, and the surface of the jacket should not have defects such as asperities. Excess inlets shall be sealed in an explosion-proof type, coated with 201-replacement rust-preventive oil, and tighten the compression nut to seal the inlet. Led Explosion-Proof Lights Where there is a strong shock, use a fall prevention ring to prevent the lamp from falling off.
Precautions
1. Regularly eliminate dust and dirt on the explosion-proof lamp housing to improve the light efficiency and heat dissipation performance of the lamp. The cleaning method can be based on the protection capability of the lamp housing, using water spray (over the shade on the lamp) or using a damp cloth. When cleaning with water spray, the power should be cut off. Never use a dry cloth to scrub the plastic housing (transparent parts) of the lamp to prevent static electricity.
2. Check whether the transparent parts have been affected by foreign material, whether the protection network has loosened, stripped, and corroded. If so, use should be stopped and repaired and replaced in time.
3. The light source should be turned off in a timely manner to notify the light to be replaced, so as to prevent the ballast and other electrical components from being in an abnormal state for a long time because the light source cannot be started.
4. If the accumulated water in the cavity of the lamp used in the humid environment should be cleared in time, replace the sealing parts to ensure the protective performance of the enclosure.
5. When you open the lamp cover, you should press the warning board to open the cover after turning off the power.
6. After opening the cover, check whether the flameproof joint surface is intact, whether the rubber seal is hardened or becomes sticky, whether the wire insulation layer is green and carbonized, and whether the insulation and electrical components are deformed and burned. If these problems are found, they should be promptly repaired and replaced.
7. Before applying the cover, apply a damp cloth (not excessively wet) to light the light and transparent parts of the light fixture to increase the efficacy of the light fixture. A layer of 204-1 displacement rust preventive oil should be applied thinly on the flameproof joint surface. When the lid is closed, attention should be paid to whether the sealing ring plays a sealing role in the original position.
8. The sealed part of the lamp should not be frequently disassembled and opened. Patent zone road sealing technology; more in line with national explosion-proof new technology.
The BAD808 series high-power LED explosion-proof lamp light source produced by Yurong Explosion-proof Electrical Appliances (Shanghai) Co., Ltd. uses the world-leading LED and the US CREE brand, and its power consumption is only 40% of the metal halide lamp. All key power components are selected by the world's top brands, which are highly efficient and stable. The BAD808 series of high-power LED explosion-proof lamps adopts a unique heat dissipation structure, uses heat transfer and heat conduction to accelerate the heat conduction, and effectively ensure the efficient heat dissipation of the LED, thus enabling the LED lifetime to reach 100,000 hours.
<br> <br> proof lamp installation and maintenance checkup from the plate before mounting the product specification: explosion-proof type, class, grade, group; housing degree of protection; Installation and fasteners required for mounting the like. The installation of explosion-proof lights must be securely secured, the fastening bolts must not be replaced, and the spring washers should be complete. The dust-proof and waterproof seals should be placed as they are. When the cable enters the line, the cable and the sealing gasket should be closely matched. The section of the cable should be round, and the surface of the jacket should not have defects such as asperities. Excess inlets shall be sealed in an explosion-proof type, coated with 201-replacement rust-preventive oil, and tighten the compression nut to seal the inlet. Led Explosion-Proof Lights Where there is a strong shock, use a fall prevention ring to prevent the lamp from falling off.
Precautions
1. Regularly eliminate dust and dirt on the explosion-proof lamp housing to improve the light efficiency and heat dissipation performance of the lamp. The cleaning method can be based on the protection capability of the lamp housing, using water spray (over the shade on the lamp) or using a damp cloth. When cleaning with water spray, the power should be cut off. Never use a dry cloth to scrub the plastic housing (transparent parts) of the lamp to prevent static electricity.
2. Check whether the transparent parts have been affected by foreign material, whether the protection network has loosened, stripped, and corroded. If so, use should be stopped and repaired and replaced in time.
3. The light source should be turned off in a timely manner to notify the light to be replaced, so as to prevent the ballast and other electrical components from being in an abnormal state for a long time because the light source cannot be started.
4. If the accumulated water in the cavity of the lamp used in the humid environment should be cleared in time, replace the sealing parts to ensure the protective performance of the enclosure.
5. When you open the lamp cover, you should press the warning board to open the cover after turning off the power.
6. After opening the cover, check whether the flameproof joint surface is intact, whether the rubber seal is hardened or becomes sticky, whether the wire insulation layer is green and carbonized, and whether the insulation and electrical components are deformed and burned. If these problems are found, they should be promptly repaired and replaced.
7. Before applying the cover, apply a damp cloth (not excessively wet) to light the light and transparent parts of the light fixture to increase the efficacy of the light fixture. A layer of 204-1 displacement rust preventive oil should be applied thinly on the flameproof joint surface. When the lid is closed, attention should be paid to whether the sealing ring plays a sealing role in the original position.
8. The sealed part of the lamp should not be frequently disassembled and opened. Patent zone road sealing technology; more in line with national explosion-proof new technology.
The BAD808 series high-power LED explosion-proof lamp light source produced by Yurong Explosion-proof Electrical Appliances (Shanghai) Co., Ltd. uses the world-leading LED and the US CREE brand, and its power consumption is only 40% of the metal halide lamp. All key power components are selected by the world's top brands, which are highly efficient and stable. The BAD808 series of high-power LED explosion-proof lamps adopts a unique heat dissipation structure, uses heat transfer and heat conduction to accelerate the heat conduction, and effectively ensure the efficient heat dissipation of the LED, thus enabling the LED lifetime to reach 100,000 hours.
HANMAC have professional workers for packing Aluminum Weld Neck Flange. So that we can make sure that the packing for Aluminum 1060 Welding Neck Flange is safely. Some trial order for Aluminum 6061 Wn Flange , Aluminum 5083 Weld Neck Flange could be done in one week.
We can offer high quality aluminum weld neck flanges.
Our production scope: ASTM/ASME/ANSIB16.5, B16.47, ASME/ANSIB16.48 flange Slip On Flange , Weld Neck Flange Threaded Flange Blind Flange
Size: 1/2"-120" (DN15-DN3000)
Pressure: Class150-Class2500
Material: 1060,5083,6061 and their temper T6
Standard: ASTM/ASME/ANSIB16.5, ASME/ANSI B16.3and B16.47, ASME/ANSIB16.42, JIS/KS (5K, 10K, 16K, 20K), DIN2633, DIN2634, DIN2635,EN1092,BS4504,,Customized drawings
Inspection: In house and third party
Document: MTC Comply with EN10204 3.1 can be provided prior to shipment
Aluminum Weld Neck Flange, Aluminum 1060 Welding Neck Flange, Aluminum 6061 Wn Flange, Aluminum 5083 Weld Neck Flange
HEBEI HANMAC MACHINE CO., LTD. , https://www.chinahanmac.com