Due to improper use of the hydraulic system or component failure, the hydraulic system will heat up.
Due to improper use of the hydraulic system or component failure, the hydraulic system will heat up. The specific causes and solutions for fever are detailed in the following four points:

1. The hydraulic oil level in the fuel tank is lower than the lowest liquid level, which reduces the heat dissipation power of the fuel tank.

Solution: During the use, it is necessary to observe the oil level of the hydraulic oil in the fuel tank at all times, and always maintain the hydraulic oil level in the normal oil level range, thus ensuring the heat dissipation effect of the fuel tank. When the hydraulic oil level in the fuel tank is lower than the oil level When filling the lowest level, it is necessary to fill the tank with oil in time.

2. The cooling effect of the cooler is reduced to warm the oil.

The cooling effect of the system heating cooler is reduced, which may be caused by the following reasons:

1 The internal blockage of the cooler or the surface dirt is more, causing the cooler safety device to open, the cooler over flow to decrease, the heat dissipation flow to be reduced, or the cooler to be poorly ventilated, so that the cooling heat transfer coefficient of the cooler is lowered, and the cooling effect is lowered. Therefore, it is necessary to check regularly during use, dredge the cooler, and regularly remove the dirt on the surface of the cooler to ensure the smooth internal and external cleaning of the cooler to ensure the cooling effect of the cooler.

2 The opening pressure of the cooler safety valve or the check valve is lower than the standard value, so that the cooler safety protection device is opened when the cooler is not blocked, and an overflow shunt is generated to reduce the heat dissipation flow of the cooler. Therefore, before the cooler is used, the opening pressure of the safety protection device must be properly adjusted. During the use, the opening pressure value of the safety protection device should be checked and corrected periodically.

3, hydraulic system pressure adjustment is improper, due to performance requirements, the system is often equipped with safety valves, relief valves and sequence valves. If the pressure of the safety valve is too low, the safety valve will open frequently, causing overflow loss, which will cause the system to heat up; if the pressure is adjusted too high, the leakage in the system will increase and the system will heat up.

Solution: The safety valve and pressure values ​​should be correctly calculated and adjusted according to the load requirements of the hydraulic system to ensure that the system works within the specified pressure range.

4. Increased internal leakage can increase oil temperature. The internal leakage of the hydraulic system includes the internal leakage of the hydraulic pump, the hydraulic cylinder, the hydraulic motor and the hydraulic valve. During the leakage process, the pressure drops and the temperature rises. If the internal leakage of the system increases, the oil temperature will rise and the system will overheat. In severe cases, the system pressure will drop, the pumping will be weak, the pumping displacement will be reduced, the stirring will be weak, and the stirring speed will decrease.

Solution: Regularly inspect these components, replace the corresponding sealing components regularly, replace or repair damaged or strained parts in time, and even replace the corresponding hydraulic components to avoid system heating caused by component leakage.







----- Editor-in-Chief: Dalan Oil Pump Motor 02-Procurement Consultant

Copyright http: / (Dalan Motor) Reprint, please indicate the source
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn

Our company specializes in providing commercial rubber sheets to consumers across the continent. Our inventory of sheet rubber consists of various different types of Elastoplast. Each of these rubber products is meant for different types of uses. Some of them, like a natural gum Rubber Sheet, are great for use as general sealing materials. Others, such as a silicone sheet rubber rolls, are meant for specific applications involving very high or very low temperatures. 1.With careful compounding,has really good tensile strength.

2.Low permeability to air and other gases.

3.Excellent resistance to ozone, oxidation and sunlight.

4.Excellent temperature range of -45°C to +130°C for normal compounds and even better with

special formulations.

5.Low resilience,ideal for vibration damping and shock absorption applications.

6.Moderate resistance to abrasion and compression set.

7.Highly resistant to mineral acids, alkaline and aqueous acids.

    

Industrial Rubber Sheet

Industrial Rubber Sheet,Rubber Sheet,Industrial Rubber Foam Sheet,Waterproof Rubber Sheet

Renqiu Xingcheng Rubber Products Co., Ltd. , https://www.rubbermats.nl