Things to pay attention to in cabinet measurement

Cabinet measurement process

1. Measure the distance from the left side of the window to the left side wall.

2. Measure the distance from the right side of the window to the right wall or column.

3, measuring the height of the window

4, measuring the height of the window sill from the ground

5, measuring layer height

Cabinet measurement considerations

1, the selection of materials should pay attention to the selection of high-quality plates, pay attention to environmental protection, bearing capacity, deformation, nailing, easy to scrub and other issues.

2. Pay attention to the construction of detail parts such as veneering and sealing.

3, pay attention to the installation of hardware accessories.

4, as much as possible to simplify the line when making, pay attention to the shape.

5, pay attention to the details of the internal water and electricity facilities, such as: the hidden pipeline, the use of space.

Cabinet measurement details

1. It is best to measure the length twice, from left to right and from right to left, so as not to look at the wrong size for the first time.

2. When measuring the height of the ceiling, it is necessary to measure the quasi-high points in several different directions, and at the same time, there are no beams under the gusset plate.

3. When measuring, look at the waist line, the bottom of the motorized socket to the height of the floor tile, and at the same time, look at the height of the window (more on the retest, pay attention to when measuring).

4. When measuring, the distance and height of the gas meter and the pipeline from the wall, the height of the flue, the height of the inlet and outlet, the distance of the drainage main, the distance from the wall, the height of the socket (retesting), etc.

5. When measuring, it is necessary to see whether there are steps on the ground, whether there are concave and convex beams on the wall, and when pulling the cabinet by the window, the pulling of the screen should be considered. If the cabinet is concerned, the relevant dimensions should be measured.

6. When the retest is done, the floor tiles should be paved and the wall tiles should be affixed. If the wall cabinet or the high cabinet is to the top, the roof should be hanged to retest.

7. When measuring irregular shapes or polygons, it is best to choose the fixed point and the amount of diagonal line. When the two sides are made of cabinets (ground and hanging cabinets), the inner and outer distances should be measured.

8. When there are poor bricks, it is necessary to measure the distance and height of the wall (including the height of the bottom and top to the ground). The normal refrigerator position is preferably 700mm long, and the special additional length is reserved.

9. The thickness of the door cover should be measured and the thickness of the door cover (including the line), or the floor with the sliding door, the hanging cabinet should open the sliding door and leave a gap of 10-20mm.

10. When measuring the kitchen of the unit, pay attention to whether the wall is a stone wall or not, so that the wall cabinet cannot be installed.

[Scan the QR code below, pay attention to the WeChat public number "Jiuzheng cabinet network "; you can view the popular article "The difference between the annual income of 5 million and the monthly income of 5,000 yuan ", and want to communicate with peers to join the Jiuzheng building materials network cabinet exchange group]

PCD Cutting Inserts 

PCD cutting inserts are used to machining for cast iron, non-ferrous materials, high-temp alloys, hardend materials.  


PCD turning inserts are widely used to replace cemented Carbide Inserts in the processing industry, especillay for cutting Alumimium alloy, copper and Non-Ferros metal. Although the unit price is higher than the traditional cemented carbide inserts, but performas is much more better than other carbide inserts, as it can greatly improve the processing efficiency and service life, ensure the workpiece surface processing accuracy, especially for mirror finishing. At the same time, some of the PCD turing inserts can be repaired several times, the cost of the PCD turning inserts are even lower than that of the carbide inserts.


product catagory  

Diamond inserts identification


PRODUCT DETAIL:

pcd cutting inserts


pcd cutting insertspcd cutting insertspcd cutting insertspcd cutting insertspcd cutting insertspcd cutting inserts





4product detail-fanyi

PRODUCT EQUIPMENT:

product equipment


Flexible in order quantity:

Samples can be provided before mass production, and MOQ can be discussed accordingly.

 

About us:

We are specialize in manufacturing PCD diamond tools and Carbide tools. 


Our major product include PCD Inserts , PCD Reamers , PCD End Mill , PCD Taps, Carbide Inserts, Carbide Drills, Carbide Reams, Taps etc.. Premium quality of raw material is used in the production and strict examination during processing with advanced equipment. 


Our best selling of cutting tools include PCD Inserts, PCD End Mill , PCD Ball Nose Mill, PCD Reamer , Carbide Taps , Carbide End Mill, Special Form Cutter and many more.

 PCD Inserts

If you encounter problems such as high-speed, high precision requirements, low tool life and so on in the processing, you may contact us to recommend appropriate design for you, we can provide customization per your drawing. Looking forward to make a long business relationship with you.


quanlity control:


We have dedicated team of quality control and precise equipment to keep good and stable performance for our products and processing services.

great service





PCD Turning Inserts

PCD Cutting Inserts,Cutting Insert,Diamond Turning Inserts,Insert Cutting Tool

OPT Cutting Tools Co., Ltd. , https://www.optdiamondtools.com